Vulcanizing solution - tube patches - set No.0 (Ø 30 mm)
Info Rubber glue 5g (1/6 oz.) 10-Pack (SVS-VULC)
The rubber and neoprene glue for rubber and neoprene fishing tackle and outdoor tackle for example for rubber boots, wading trousers, rubber boats, surfer clothes, wheel hoses & many other rubber & Neoprene products.
Info Tube Patches No. 0 Ø 30 mm Red Edge
The repair patch for rubber and neoprene.
Info about the brushes
Plastic brush with natural bristles for safe/easy spreading of the vulcanizing solution. Scope of delivery: 10 brushes with a total length of 68 mm and a bristle width of approx. 5 mm
Bike tube repair instructions
Slightly roughen the area to be repaired with the buffing paper (slightly larger than the patch). Apply a thin layer of vulcanizing solution to the roughened surface, massage in with a brush and leave on for 5 minutes. Remove the aluminum foil from the patch, put it on and press down firmly, starting from the middle. Before inserting the hose, let it dry for at least 10 minutes, preferably longer.
Rubber Repair Guide
Slightly roughen the area to be repaired with the buffing paper (slightly larger than the patch). Apply a thin layer of the vulcanizing solution to the roughened surface, massage in with a brush and leave on for at least 5 minutes. Remove the aluminum foil from the patch, put it on and press down firmly, starting from the middle. Let the bond rest for at least 30 minutes. The bonded area can then be easily loaded. The repair can be fully loaded after approx. 2 - 3 hours.
Neoprene repair guide
Apply vulcanizing solution to the area to be repaired and massage in with a brush (slightly larger than the patch). Allow the vulcanizing solution to take effect for at least 5 minutes. Then apply a 2nd coat of vulcanizing solution to the 1st coat and massage in with the brush, but only allow it to take effect for a short time! Remove the aluminum foil from the patch, put it on and press down firmly, starting from the middle. Allow the bond to rest for at least 60 minutes. The bonded area can then be easily loaded. The repair can be fully loaded after approx. 2 - 3 hours.
Scope of supply
- 1 original pack of 100 REMA TIP TOP tube patches No.0 (Ø 30 mm) red edge
- 10 Rubber glue 5g SVS-VULC (1/6 oz.)
- 10-pieces Brush 68 mm long and
- a 4-page detailed product description in German with instructions for use.
Avoid direct sunlight and drafts when making repairs/gluing! Temperatures below 5°C can have a negative impact on the repair result.
Storage/ shelf life
The optimal storage is dark, cool (15-25°C) and dry. If the recommended storage conditions are adhered to, the hose patches and the vulcanizing solution can be stored for many years without any quality restrictions.
Hazards for SVS-VULC
Danger
Hazardous components which must be listed on the label: Naphtha (petroleum)
Hazard statements: Highly flammable liquid and vapour. Causes skin irritation. May cause drowsiness or dizziness. Toxic to aquatic life with long lasting effects.
Precautionary statements: Keep out of reach of children. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Wear protective gloves/protective clothing/eye protection/face protection. IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Call a POISON CENTER or doctor/physician if you feel unwell. Avoid release to the environment. Dispose of contents/container to waste treatment facility in accordance with local and national regulations.
Other hazards: Vapours may form explosive mixture with air.
Safety data sheet
Unfortunately there are no review yet. Be the first who rate this product.