2-Pack PVC-& PU-REPAIR KIT XXL
.png "fishingglue.de")
2-Pack PVC-& PU-REPAIR KIT XXL
The XXL repair kit for PVC, Fabric and PU (Polyurethan) fishing tackle and outdoor tackle for example for PVC- boots, PVC-wading boots, wading trousers, PVC-boats, tents, screens, surf sails, rain clothing, boat seats and many other PVC, imitation leather and PU-articles.
Scope of supply (for a single PVC & PU REPAIR SET XXL)
- 2 tube adhesive 6 g
- 1 transparent patch 300 x 75 mm
- 2 transparent round patches in the diameter 45 mm
- 2 transparent patches 75 x 40 mm
- 2 sandpaper
- 2 brush and
- Operating Instruction
Dimensions (L x B x H) (for a single PVC & PU REPAIR SET XXL)
approx. 118 x 70 x 22 mm
wight: 70 g
Operating Instruction
Application with articles from PVC, with PVC surface, PU and imitation leather
The place with the sandpaper, which can be repaired, easily sharpen (somewhat more largely than the patch). The adhesive on the polished place and on the patches give and with the brush evenly thinly distribute. Adhesive 1- max. 2 minutes to influence leave. Beginning outward and at least 5 minutes present the patch and press in slightly firmly of the center under pressure left (e.g. with the hand). The stuck together place is then easily loadable. The repair is fully loadable after approximately 2-3 hours.
Application with articles from fabric and with fabric surface
The place with the sandpaper which can be repaired, easily sharpen (somewhat more largely than the patch). On the polished place a sufficient quantity adhesive gives and with the brush distributes, to rub in and approx. 20-30 minutes influence leaves. Then the 2nd adhesive spreader on the 1st spreader and the patches lie on and with the brush evenly distribute. The adhesive 1- max. 2 minutes to influence leave. Beginning outward and at least 5 minutes present the patch and press in slightly firmly of the center under pressure left (e.g. with the hand). The stuck together place is then easily loadable. The repair is fully loadable after approximately 2-3 hours.
The bearing and the Waring-temperature should be 10-25°C. Below 5°C can be contained in the package and adhesive partially crystallize thicken. When heated to room temperature, however, crystallized products are re-usable.
The XXL repair kit for PVC, Fabric and PU (Polyurethan) fishing tackle and outdoor tackle for example for PVC- boots, PVC-wading boots, wading trousers, PVC-boats, tents, screens, surf sails, rain clothing, boat seats and many other PVC, imitation leather and PU-articles.
Scope of supply (for a single PVC & PU REPAIR SET XXL)
- 2 tube adhesive 6 g
- 1 transparent patch 300 x 75 mm
- 2 transparent round patches in the diameter 45 mm
- 2 transparent patches 75 x 40 mm
- 2 sandpaper
- 2 brush and
- Operating Instruction
Dimensions (L x B x H) (for a single PVC & PU REPAIR SET XXL)
approx. 118 x 70 x 22 mm
wight: 70 g
Operating Instruction
Application with articles from PVC, with PVC surface, PU and imitation leather
The place with the sandpaper, which can be repaired, easily sharpen (somewhat more largely than the patch). The adhesive on the polished place and on the patches give and with the brush evenly thinly distribute. Adhesive 1- max. 2 minutes to influence leave. Beginning outward and at least 5 minutes present the patch and press in slightly firmly of the center under pressure left (e.g. with the hand). The stuck together place is then easily loadable. The repair is fully loadable after approximately 2-3 hours.
Application with articles from fabric and with fabric surface
The place with the sandpaper which can be repaired, easily sharpen (somewhat more largely than the patch). On the polished place a sufficient quantity adhesive gives and with the brush distributes, to rub in and approx. 20-30 minutes influence leaves. Then the 2nd adhesive spreader on the 1st spreader and the patches lie on and with the brush evenly distribute. The adhesive 1- max. 2 minutes to influence leave. Beginning outward and at least 5 minutes present the patch and press in slightly firmly of the center under pressure left (e.g. with the hand). The stuck together place is then easily loadable. The repair is fully loadable after approximately 2-3 hours.
The bearing and the Waring-temperature should be 10-25°C. Below 5°C can be contained in the package and adhesive partially crystallize thicken. When heated to room temperature, however, crystallized products are re-usable.
Hazards for the PVC- and PU Glue:
Danger
Hazardous components which must be listed on the label: Butanone
Hazard statements: Highly flammable liquid and vapour. Causes serious eye irritation. May cause drowsiness or dizziness.
Precautionary statements: Keep out of reach of children. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Keep container tightly closed. Wear protective gloves/protective clothing/eye protection/face protection. IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower. IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Store in a well-ventilated place. Keep container tightly closed. Dispose of contents/container to in accordance with local and national regulations.
Special labelling of certain mixtures: Repeated exposure may cause skin dryness or cracking.
Other hazards: Vapours may form explosive mixture with air.
Safety data sheet
Danger
Hazardous components which must be listed on the label: Butanone
Hazard statements: Highly flammable liquid and vapour. Causes serious eye irritation. May cause drowsiness or dizziness.
Precautionary statements: Keep out of reach of children. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Keep container tightly closed. Wear protective gloves/protective clothing/eye protection/face protection. IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower. IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Store in a well-ventilated place. Keep container tightly closed. Dispose of contents/container to in accordance with local and national regulations.
Special labelling of certain mixtures: Repeated exposure may cause skin dryness or cracking.
Other hazards: Vapours may form explosive mixture with air.
Safety data sheet
Hersteller/EU Verantwortliche Person/Produktdokumente
Hersteller:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
E-Mail
info@fishingglue.de
Telefon
081212279007
EU Verantwortliche Person:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
E-Mail
info@fishingglue.de
Telefon
081212279007
Produktdokumente:
Datenblatt PVC-& PU-REPARATUR-SET XXL
Sicherheitsdatenblatt PVC-& PU-Reparaturset und PVC-& PU-Kleber
Hersteller:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
info@fishingglue.de
Telefon
081212279007
EU Verantwortliche Person:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
info@fishingglue.de
Telefon
081212279007
Produktdokumente:
Datenblatt PVC-& PU-REPARATUR-SET XXL
Sicherheitsdatenblatt PVC-& PU-Reparaturset und PVC-& PU-Kleber
