Stinger Magnet "Vertical" single magnet
.png "fishingglue.de")
Stinger Magnet "Vertical" single magnet (saltwater resistant!)
Our "Vertikal" Stinger magnets are small, black high-quality N52 neodymium permanent magnets for modern and perfect fear hook fixation when fishing vertically with soft baits. However, their adhesive power is often sufficient for spin fishing, trolling and jigging with smaller baits up to approx. 12 cm in length. Due to the special plastic coating and when using the Soft Bait Glue, the magnets are excellently protected against corrosion and are therefore also ideally suited for sea fishing. For many years, our magnets have proven themselves thousands of times over in the Royber jigs, which are particularly popular among sea anglers.
With the fishingglue Soft Bait Glue, the fishingglue Stinger magnets with their special coating can be glued very easily and permanently to almost all soft baits. Also on soft baits with a very high proportion of softeners as well as salted and flavored baits!
Danger! Our Soft Bait Glue and the coating of the magnets are not suitable for all softener-free soft baits from Moby made from Non Toxic Material, Z-Man soft baits from ElaZtech or baits made from similar material. Also not suitable for all soft baits from the company PROFIBLINKER.
Instructions for gluing with the fishingglue - Soft Bait Glue
Please make sure that the work area is not magnetic/metallic when gluing and that the magnets are not pulled off the soft bait by metal parts such as zippers, pliers, etc.) before the glue point has set.
1. First use the stinger to determine the spot where the magnet should be attached to the soft bait. Since the bait stretches when thrown, the distance should be slightly shorter than the actual length of the stinger! > Mark the spot!
2. If necessary, clean & dry the splice and remove the softener.
3. With very soft baits, slightly roughen the sticking point with the included buffing paper!
4. Apply Soft Bait Glue and massage in with the dosing tip and do not let it dry!
5. Place the stinger magnet on the still wet adhesive and press briefly and firmly. After 1 - 2 minutes, briefly press the glued magnet down again and seal the edges/transitions to the soft bait with some Soft Bait Glue.
6. Let the Soft Bait with the glued magnet dry for at least 30 minutes.
Avoid direct sunlight and draughts for every repair/bonding!
Temperatures below 5°C can negatively affect the bonding!
Specification
- N52 neodymium permanent magnets for attaching fear hooks to Soft Baits
- Dimensions of single magnet approx. 9 x 4 x 2,5 mm (L x B x H)
- Weight of a magnet about 0,6 g
Form of delivery
- Your desired quantity (at least 20 pieces) Stinger Magnet "Spin & Jig" in a ziplock bag + fishingglue descriptionee
- 1 rough paper approx. 30 x 40 mm
- 1 detailed instruction for gluing to Soft Baits inside
Direction of magnetization
axially in the transverse direction, through the height of 2,5 mm
Storage/ shelf life
The storage and application temperature should ideally be 10 - 25°C. If the recommended storage temperature is observed, the STINGER MAGNETS can be stored for many years.
Example video for gluing the STINGER MAGNET to the soft bait
Our "Vertikal" Stinger magnets are small, black high-quality N52 neodymium permanent magnets for modern and perfect fear hook fixation when fishing vertically with soft baits. However, their adhesive power is often sufficient for spin fishing, trolling and jigging with smaller baits up to approx. 12 cm in length. Due to the special plastic coating and when using the Soft Bait Glue, the magnets are excellently protected against corrosion and are therefore also ideally suited for sea fishing. For many years, our magnets have proven themselves thousands of times over in the Royber jigs, which are particularly popular among sea anglers.
With the fishingglue Soft Bait Glue, the fishingglue Stinger magnets with their special coating can be glued very easily and permanently to almost all soft baits. Also on soft baits with a very high proportion of softeners as well as salted and flavored baits!
Danger! Our Soft Bait Glue and the coating of the magnets are not suitable for all softener-free soft baits from Moby made from Non Toxic Material, Z-Man soft baits from ElaZtech or baits made from similar material. Also not suitable for all soft baits from the company PROFIBLINKER.
Instructions for gluing with the fishingglue - Soft Bait Glue
Please make sure that the work area is not magnetic/metallic when gluing and that the magnets are not pulled off the soft bait by metal parts such as zippers, pliers, etc.) before the glue point has set.
1. First use the stinger to determine the spot where the magnet should be attached to the soft bait. Since the bait stretches when thrown, the distance should be slightly shorter than the actual length of the stinger! > Mark the spot!
2. If necessary, clean & dry the splice and remove the softener.
3. With very soft baits, slightly roughen the sticking point with the included buffing paper!
4. Apply Soft Bait Glue and massage in with the dosing tip and do not let it dry!
5. Place the stinger magnet on the still wet adhesive and press briefly and firmly. After 1 - 2 minutes, briefly press the glued magnet down again and seal the edges/transitions to the soft bait with some Soft Bait Glue.
6. Let the Soft Bait with the glued magnet dry for at least 30 minutes.
Avoid direct sunlight and draughts for every repair/bonding!
Temperatures below 5°C can negatively affect the bonding!
Specification
- N52 neodymium permanent magnets for attaching fear hooks to Soft Baits
- Dimensions of single magnet approx. 9 x 4 x 2,5 mm (L x B x H)
- Weight of a magnet about 0,6 g
Form of delivery
- Your desired quantity (at least 20 pieces) Stinger Magnet "Spin & Jig" in a ziplock bag + fishingglue descriptionee
- 1 rough paper approx. 30 x 40 mm
- 1 detailed instruction for gluing to Soft Baits inside
Direction of magnetization
axially in the transverse direction, through the height of 2,5 mm
Storage/ shelf life
The storage and application temperature should ideally be 10 - 25°C. If the recommended storage temperature is observed, the STINGER MAGNETS can be stored for many years.
Example video for gluing the STINGER MAGNET to the soft bait
Hersteller/EU Verantwortliche Person/Produktdokumente
Hersteller:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
E-Mail
info@fishingglue.de
Telefon
081212279007
EU Verantwortliche Person:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
E-Mail
info@fishingglue.de
Telefon
081212279007
Produktdokumente:
Produktbeschreibung/ Produktflyer mit allgemeinen Warnhinweisen
Hersteller:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
info@fishingglue.de
Telefon
081212279007
EU Verantwortliche Person:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
info@fishingglue.de
Telefon
081212279007
Produktdokumente:
Produktbeschreibung/ Produktflyer mit allgemeinen Warnhinweisen
