fishingglue Predator System 14-16 cm; Model: Wire Lead Free Chartreuse
.png "fishingglue.de")
FISHINGGLUE PREDATOR SYSTEM 14-16 cm
Model: WIRE LEAD FREE CHARTREUSE
The FISHINGGLUE PREDATOR SYSTEM 14-16 cm; Model: WIRE LEAD FREE CHARTREUSE is the largest wire body bait system in our lead-free range range with a very eye-catching Chartreuse tungsten head for that extra appeal. And with the option to choose between 6 Lead heads of different weights, everyone will find a suitable system for their situation. Designed for bait fish from 14 - 16 cm in length, this system size is mainly used for fishing for the larger specimens of the target fish: pike and zander. For your safety, each individual predatory fish system 14-16 cm is checked by us before packing with regard to the system load capacity of at least 10 kg that we specify. In order to achieve this high breaking strain, the relatively "weak" metal clamp on the built-in Cheburashka head is replaced with a high-strength steel leader loop.
For a good or optimal bait run, we recommend the use of rather slim bait fish such as roach or bleak. With a little practice and our instructions, which are included with each item in the packaging, the assembly of the bait fish on the FISHINGGLUE PREDICTION SYSTEM is quick and easy.
Note that some parts, especially the treble hooks, are sharp or pointed and can cause injuries if handled carelessly. Therefore, FISHINGGLUE PREDATOR SYSTEMS should always be kept in the original packaging, stored and kept away from children.
Specification
- Bait Fish System for spin fishing with dead bait fish with a length of 14 – 16 cm
- installed treble hooks 2 x size 4
- Individually tested load capacity of each predatory fish system: 10 kg
- Dimensions (including packaging) approx. 120 x 40 x 22 mm (L x W x H)
Varianten fishingglue-Raubfischsystem 14-16 cm; Modell: Draht bleifrei Chartreuse
Model: WIRE LEAD FREE CHARTREUSE
The FISHINGGLUE PREDATOR SYSTEM 14-16 cm; Model: WIRE LEAD FREE CHARTREUSE is the largest wire body bait system in our lead-free range range with a very eye-catching Chartreuse tungsten head for that extra appeal. And with the option to choose between 6 Lead heads of different weights, everyone will find a suitable system for their situation. Designed for bait fish from 14 - 16 cm in length, this system size is mainly used for fishing for the larger specimens of the target fish: pike and zander. For your safety, each individual predatory fish system 14-16 cm is checked by us before packing with regard to the system load capacity of at least 10 kg that we specify. In order to achieve this high breaking strain, the relatively "weak" metal clamp on the built-in Cheburashka head is replaced with a high-strength steel leader loop.
For a good or optimal bait run, we recommend the use of rather slim bait fish such as roach or bleak. With a little practice and our instructions, which are included with each item in the packaging, the assembly of the bait fish on the FISHINGGLUE PREDICTION SYSTEM is quick and easy.
Note that some parts, especially the treble hooks, are sharp or pointed and can cause injuries if handled carelessly. Therefore, FISHINGGLUE PREDATOR SYSTEMS should always be kept in the original packaging, stored and kept away from children.
Specification
- Bait Fish System for spin fishing with dead bait fish with a length of 14 – 16 cm
- installed treble hooks 2 x size 4
- Individually tested load capacity of each predatory fish system: 10 kg
- Dimensions (including packaging) approx. 120 x 40 x 22 mm (L x W x H)
Varianten fishingglue-Raubfischsystem 14-16 cm; Modell: Draht bleifrei Chartreuse
|
Irtem number
|
Head weight
|
Price in €
|
|
999107-04
|
4 g
|
7,35
|
|
999107-06
|
6 g
|
7,85
|
|
999107-08
|
8 g
|
8,15
|
|
999107-10
|
10 g
|
8,35
|
|
999107-12
|
12 g
|
8,65
|
|
999107-14
|
14 g
|
8,85
|
Form of delivery
in a sturdy resealable plastic box:
- 1 Piece fishingglue Predator System 14-16 cm; Model: Wire Lead Free Chartreuse
- A German-language manual for mounting the baitfish on the system
Our service
The various parts of the FISHINGGLUE PREDATOR SYSTEMS can be purchased individually from us and replaced or supplemented as required. Due to the modular structure of our FISHINGGLUE PREDATOR SYSTEMS, many components can be interchanged or combined with one another. > PREDATOR SYSTEM PARTS
in a sturdy resealable plastic box:
- 1 Piece fishingglue Predator System 14-16 cm; Model: Wire Lead Free Chartreuse
- A German-language manual for mounting the baitfish on the system
Our service
The various parts of the FISHINGGLUE PREDATOR SYSTEMS can be purchased individually from us and replaced or supplemented as required. Due to the modular structure of our FISHINGGLUE PREDATOR SYSTEMS, many components can be interchanged or combined with one another. > PREDATOR SYSTEM PARTS
Instructions for mounting the bait fish on the predatory fish system
1. After unpacking the Predator System, stretch the copper wire to line up with the Predator System body.
2. Insert the predator system body, with the copper wire first, into the mouth of the baitfish and guide the copper wire back out of a gill opening of the baitfish.
3. Now push the predatory fish system body further into the bait fish up to the eyelet and always pull the copper wire that was led out of the gills with it.
4. Now pierce the copper wire about 2 cm behind the gill opening from which it came out through the middle of the baitfish (below the spine). Then wrap the copper wire around the baitfish and finally insert the end of the copper wire into the baitfish.
5. Now the hooks can be attached to the underside of the bait fish. Ideally, the front treble can be "hooked" into the copper wire. The rear treble hook is inserted in the base of the baitfish's tail. If necessary, you can secure the rear treble with some "ELASTIC BAITBAND".
6. The predator system is now ready to fish.
And after fishing...
> Immediately remove "bait fish residue" from the predatory fish system after each use, rinse thoroughly with clean fresh water and allow to dry.
> The copper wire is a bit wavy or no longer smooth after each use of the system, which can be very annoying the next time you use it. However, the copper wire can easily be straightened again. Proceed as follows to smooth the copper wire: pull the copper wire under tension (held between both hands) briefly back and forth over an edge of wood.
> If something on the predatory fish system is damaged after use, the various parts of the predatory fish systems can be purchased individually from us and replaced or supplemented if necessary. Here is the link to: Predator Systems Parts
These instructions (in German script) for optimal bait fish assembly are enclosed / supplied with each predatory fish system in the item packaging.
1. After unpacking the Predator System, stretch the copper wire to line up with the Predator System body.
2. Insert the predator system body, with the copper wire first, into the mouth of the baitfish and guide the copper wire back out of a gill opening of the baitfish.
3. Now push the predatory fish system body further into the bait fish up to the eyelet and always pull the copper wire that was led out of the gills with it.
4. Now pierce the copper wire about 2 cm behind the gill opening from which it came out through the middle of the baitfish (below the spine). Then wrap the copper wire around the baitfish and finally insert the end of the copper wire into the baitfish.
5. Now the hooks can be attached to the underside of the bait fish. Ideally, the front treble can be "hooked" into the copper wire. The rear treble hook is inserted in the base of the baitfish's tail. If necessary, you can secure the rear treble with some "ELASTIC BAITBAND".
6. The predator system is now ready to fish.
And after fishing...
> Immediately remove "bait fish residue" from the predatory fish system after each use, rinse thoroughly with clean fresh water and allow to dry.
> The copper wire is a bit wavy or no longer smooth after each use of the system, which can be very annoying the next time you use it. However, the copper wire can easily be straightened again. Proceed as follows to smooth the copper wire: pull the copper wire under tension (held between both hands) briefly back and forth over an edge of wood.
> If something on the predatory fish system is damaged after use, the various parts of the predatory fish systems can be purchased individually from us and replaced or supplemented if necessary. Here is the link to: Predator Systems Parts
These instructions (in German script) for optimal bait fish assembly are enclosed / supplied with each predatory fish system in the item packaging.
Hersteller/EU Verantwortliche Person/Produktdokumente
Hersteller:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
E-Mail
info@fishingglue.de
Telefon
081212279007
EU Verantwortliche Person:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
E-Mail
info@fishingglue.de
Telefon
081212279007
Produktdokumente:
Gebrauchsanweisung fishingglue-Raubfischsysteme
Hersteller:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
info@fishingglue.de
Telefon
081212279007
EU Verantwortliche Person:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
info@fishingglue.de
Telefon
081212279007
Produktdokumente:
Gebrauchsanweisung fishingglue-Raubfischsysteme