fishingglue Predator System 14-16 cm; Model: BALSA Chatter Blade
.png "fishingglue.de")
FISHINGGLUE PREDATOR SYSTEM 14-16 cm
Model: BALSA CHATTER BLADE
Our FISHINGGLUE PREDATOR SYSTEM 14-16 cm; Model: BALSA CHATTER BLADE is the largest Chatter Blade Wire body baitfish system we offer. You have the choice between 2 different Chatter Blade colors. Designed for bait fish from 14 - 16 cm in length, this system size is mainly used for fishing for the larger specimens of the target fish: pike and zander. For your safety, each individual predatory fish system 14-16 cm is checked by us before packing with regard to the system load capacity of at least 10 kg that we specify.
For a good or optimal bait movement, no head weight is mounted on all fishingglue Chatter Blade bait fish systems, but only a small counterweight on the steel leader of the hook system. Equipped in this way, every system runs optimally, as is typical for Chatter and is primarily designed for spin fishing in the upper water layers or shallower water areas.
However, if you still want to mount a weight to allow the system to run deeper, we recommend mounting the weight between the main line and the leader (at least 30 cm in front of the bait). In this way, the desired Chatter Blade bait run is retained as far as possible.
As with all fishingglue predatory fish systems, we also recommend using slim bait fish such as roach or bleak. The assembly of the bait fish on the FISHINGGLUE PREDATOR SYSTEM is easy and quick with a little practice and our instructions, which are included in the packaging of each item.
Note that some parts, especially the treble hooks, are sharp or pointed and can cause injuries if handled carelessly. Therefore, FISHINGGLUE PREDATOR SYSTEMS should always be kept in the original packaging, stored and kept away from children.
Specification
- Bait Fish System for spin fishing with dead bait fish with a length of 14 – 16 cm
- The balsa body is completely encased in a thin plastic and is easy to clean
- installed treble hooks 2 x size 6
- Individually tested load capacity of each predatory fish system: 10 kg
- Dimensions (including packaging) approx. 120 x 40 x 22 mm (L x W x H)
Form of delivery
in a sturdy resealable plastic box:
- 1 Piece fishingglue Predator System 14-16 cm; Model: Balsa Chatter Blade
- A German-language manual for mounting the baitfish on the system
Model: BALSA CHATTER BLADE
Our FISHINGGLUE PREDATOR SYSTEM 14-16 cm; Model: BALSA CHATTER BLADE is the largest Chatter Blade Wire body baitfish system we offer. You have the choice between 2 different Chatter Blade colors. Designed for bait fish from 14 - 16 cm in length, this system size is mainly used for fishing for the larger specimens of the target fish: pike and zander. For your safety, each individual predatory fish system 14-16 cm is checked by us before packing with regard to the system load capacity of at least 10 kg that we specify.
For a good or optimal bait movement, no head weight is mounted on all fishingglue Chatter Blade bait fish systems, but only a small counterweight on the steel leader of the hook system. Equipped in this way, every system runs optimally, as is typical for Chatter and is primarily designed for spin fishing in the upper water layers or shallower water areas.
However, if you still want to mount a weight to allow the system to run deeper, we recommend mounting the weight between the main line and the leader (at least 30 cm in front of the bait). In this way, the desired Chatter Blade bait run is retained as far as possible.
As with all fishingglue predatory fish systems, we also recommend using slim bait fish such as roach or bleak. The assembly of the bait fish on the FISHINGGLUE PREDATOR SYSTEM is easy and quick with a little practice and our instructions, which are included in the packaging of each item.
Note that some parts, especially the treble hooks, are sharp or pointed and can cause injuries if handled carelessly. Therefore, FISHINGGLUE PREDATOR SYSTEMS should always be kept in the original packaging, stored and kept away from children.
Specification
- Bait Fish System for spin fishing with dead bait fish with a length of 14 – 16 cm
- The balsa body is completely encased in a thin plastic and is easy to clean
- installed treble hooks 2 x size 6
- Individually tested load capacity of each predatory fish system: 10 kg
- Dimensions (including packaging) approx. 120 x 40 x 22 mm (L x W x H)
Variants fishingglue Predator System 14-16 cm; Model: BALSA Chatter Blade
|
Item number
|
Chatter Blade Color
|
Price in €
|
|
999119-LS
|
Silver
|
7,95
|
|
999119-LG
|
Gold
|
7,95
|
in a sturdy resealable plastic box:
- 1 Piece fishingglue Predator System 14-16 cm; Model: Balsa Chatter Blade
- A German-language manual for mounting the baitfish on the system
Our service
The various parts of the FISHINGGLUE PREDATOR SYSTEMS can be purchased individually from us and replaced or supplemented as required. Due to the modular structure of our FISHINGGLUE PREDATOR SYSTEMS, many components can be interchanged or combined with one another. > PREDATOR SYSTEM PARTS
The various parts of the FISHINGGLUE PREDATOR SYSTEMS can be purchased individually from us and replaced or supplemented as required. Due to the modular structure of our FISHINGGLUE PREDATOR SYSTEMS, many components can be interchanged or combined with one another. > PREDATOR SYSTEM PARTS
Instructions for mounting the bait fish on the predatory fish system
1. After unpacking the Predator System, stretch the copper wire to line up with the Predator System body.
2. Insert the predator system body, with the copper wire first, into the mouth of the baitfish and guide the copper wire back out of a gill opening of the baitfish.
3. Now push the predatory fish system body further into the bait fish up to the eyelet and always pull the copper wire that was led out of the gills with it.
4. Now pierce the copper wire about 2 cm behind the gill opening from which it came out through the middle of the baitfish (below the spine). Then wrap the copper wire around the baitfish and finally insert the end of the copper wire into the baitfish.
5. Now the hooks can be attached to the underside of the bait fish. Ideally, the front treble can be "hooked" into the copper wire. The rear treble hook is inserted in the base of the baitfish's tail. If necessary, you can secure the rear treble with some "ELASTIC BAITBAND".
6. The predator system is now ready to fish.
And after fishing...
> Immediately remove "bait fish residue" from the predatory fish system after each use, rinse thoroughly with clean fresh water and allow to dry.
> The copper wire is a bit wavy or no longer smooth after each use of the system, which can be very annoying the next time you use it. However, the copper wire can easily be straightened again. Proceed as follows to smooth the copper wire: pull the copper wire under tension (held between both hands) briefly back and forth over an edge of wood.
> If something on the predatory fish system is damaged after use, the various parts of the predatory fish systems can be purchased individually from us and replaced or supplemented if necessary. Here is the link to: Predator Systems Parts
Instruction-PDF
These instructions (in German script) for optimal bait fish assembly are enclosed / supplied with each predatory fish system in the item packaging.
1. After unpacking the Predator System, stretch the copper wire to line up with the Predator System body.
2. Insert the predator system body, with the copper wire first, into the mouth of the baitfish and guide the copper wire back out of a gill opening of the baitfish.
3. Now push the predatory fish system body further into the bait fish up to the eyelet and always pull the copper wire that was led out of the gills with it.
4. Now pierce the copper wire about 2 cm behind the gill opening from which it came out through the middle of the baitfish (below the spine). Then wrap the copper wire around the baitfish and finally insert the end of the copper wire into the baitfish.
5. Now the hooks can be attached to the underside of the bait fish. Ideally, the front treble can be "hooked" into the copper wire. The rear treble hook is inserted in the base of the baitfish's tail. If necessary, you can secure the rear treble with some "ELASTIC BAITBAND".
6. The predator system is now ready to fish.
And after fishing...
> Immediately remove "bait fish residue" from the predatory fish system after each use, rinse thoroughly with clean fresh water and allow to dry.
> The copper wire is a bit wavy or no longer smooth after each use of the system, which can be very annoying the next time you use it. However, the copper wire can easily be straightened again. Proceed as follows to smooth the copper wire: pull the copper wire under tension (held between both hands) briefly back and forth over an edge of wood.
> If something on the predatory fish system is damaged after use, the various parts of the predatory fish systems can be purchased individually from us and replaced or supplemented if necessary. Here is the link to: Predator Systems Parts
Instruction-PDF
These instructions (in German script) for optimal bait fish assembly are enclosed / supplied with each predatory fish system in the item packaging.
Hersteller/EU Verantwortliche Person/Produktdokumente
Hersteller:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
E-Mail
info@fishingglue.de
Telefon
081212279007
EU Verantwortliche Person:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
E-Mail
info@fishingglue.de
Telefon
081212279007
Produktdokumente:
Gebrauchsanweisung fishingglue-Raubfischsysteme
Hersteller:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
info@fishingglue.de
Telefon
081212279007
EU Verantwortliche Person:
Unternehmensname
Hans-Günther Winkler
Adresse
Ahornweg 11, 85586 Poing, Bayern, DE
info@fishingglue.de
Telefon
081212279007
Produktdokumente:
Gebrauchsanweisung fishingglue-Raubfischsysteme